加速溶剂萃取-凝胶色谱净化高效液相色谱法测定动物源性食品中的胆固醇

采用加速溶剂萃取-凝胶色谱净化建立了动物源性食品中胆固醇检测的高效液相色谱方法。结果表明,胆固醇浓度在1.0~40.0mg/L范围内线性关系良好,加标回收率为89.1%~99.8%,相对标准偏差为3.1%~7.8%。该方法准确、灵敏度高,适用于富含脂类的动物源性食品中胆固醇的检测。     

二氧化碳/环氧丙烷/马来酸酐三元共聚物对PPC/PHB共混物力学性能的影响

采用稀土三元催化剂制备了二氧化碳-环氧丙烷-马来酸酐三元共聚物(PPCMA).用红外和核磁谱图确定了PPCMA的结构及马来酸酐单元的含量,3 wt％马来酸酐投料量的PPCMA(共聚物中马来酸酐单元含量4.1％)的玻璃化转变温度(Tg)和起始热分解温度(Td-5％)分别为13.4℃和217℃,拉伸强度为2.88 MPa,断裂伸长率为1669％,与二氧化碳-环氧丙烷共聚物(PPC)相比,引入少量马来酸酐的PPCMA有望成为一种韧性材料,并可对PPC和聚3-羟基丁酸酯(PHB)共混体系进行改性.当在PPC/PHB共混体系中添加10 wt％的PPCMA时,所得共混材料的拉伸强度为18.2 MPa,断裂伸长率则提高到85％,较没有添加PPCMA的样品提高了4.25倍,因此PPCMA的加入能有效提高PPC/PHB共混体系的韧性,改善PPC/PHB共混体系的力学性能.偏光显微镜的研究表明PPC/PHB共混体系加入PPCMA后,很快形成大量尺寸小的PHB球晶,且结晶速度大幅度提高,因此PPCMA在一定意义上可视为一种特殊的“成核剂”.     

Photocatalytically Renewable Micro‐electrochemical Sensor for Real‐Time Monitoring of Cells

Electrode fouling and passivation is a substantial and inevitable limitation in electrochemical biosensing, and it is a great challenge to efficiently remove the contaminant without changing the surface structure and electrochemical performance. Herein, we propose a versatile and efficient strategy based on photocatalytic cleaning to construct renewable electrochemical sensors for cell analysis. This kind of sensor was fabricated by controllable assembly of reduced graphene oxide (RGO) and TiO₂ to form a sandwiching RGO@TiO₂ structure, followed by deposition of Au nanoparticles (NPs) onto the RGO shell. The Au NPs‐RGO composite shell provides high electrochemical performance. Meanwhile, the encapsulated TiO₂ ensures an excellent photocatalytic cleaning property. Application of this renewable microsensor for detection of nitric oxide (NO) release from cells demonstrates the great potential of this strategy in electrode regeneration and biosensing.     

Feasibility of ultra-high performance liquid and gas chromatography coupled to mass spectrometry for accurate determination of primary and secondary phthalate metabolites in urine samples

Phthalates (PAEs) are ubiquitous toxic chemical compounds. During the last few years, some phthalate metabolites (MPAEs) have been proposed as appropriate biomarkers in human urine samples to determine PAE human intake and exposure. So, it is necessary to have fast, easy, robust and validated analytical methods to determine selected MPAEs in urine human samples. Two different instrumental methods based on gas (GC) and ultra-high performance liquid (UHPLC) chromatography coupled to mass spectrometry (MS) have been optimized, characterized and validated for the simultaneous determination of nine primary and secondary phthalate metabolites in urine samples. Both instrumental methods have similar sensitivity (detection limits ranged from 0.03 to 8.89 pg μL⁻¹ and from 0.06 to 0.49 pg μL⁻¹ in GC–MS and UHPLC–MS², respectively), precision (repeatability, expressed as relative standard deviation, which was lower than 8.4% in both systems, except for 5OH-MEHP in the case of GC–MS) and accuracy. But some advantages of the UHPLC–MS² method, such as more selectivity and lower time in the chromatographic runs (6.8 min vs. 28.5 min), have caused the UHPLC–MS² method to be chosen to analyze the twenty one human urine samples from the general Spanish population. Regarding these samples, MEP showed the highest median concentration (68.6 μg L⁻¹), followed by MiBP (23.3 μg L⁻¹), 5cx-MEPP (22.5 μg L⁻¹) and MBP (19.3 μg L⁻¹). MMP (6.99 μg L⁻¹), 5oxo-MEHP (6.15 μg L⁻¹), 5OH-MEHP (5.30 μg L⁻¹) and MEHP (4.40 μg L⁻¹) showed intermediate levels. Finally, the lowest levels were found for MBzP (2.55 μg L⁻¹). These data are within the same order of magnitude as those found in other similar populations.     

Tutorial review on validation of liquid chromatography–mass spectrometry methods: Part I

This is the part I of a tutorial review intending to give an overview of the state of the art of method validation in liquid chromatography mass spectrometry (LC–MS) and discuss specific issues that arise with MS (and MS/MS) detection in LC (as opposed to the “conventional” detectors). The Part I briefly introduces the principles of operation of LC–MS (emphasizing the aspects important from the validation point of view, in particular the ionization process and ionization suppression/enhancement); reviews the main validation guideline documents and discusses in detail the following performance parameters: selectivity/specificity/identity, ruggedness/robustness, limit of detection, limit of quantification, decision limit and detection capability. With every method performance characteristic its essence and terminology are addressed, the current status of treating it is reviewed and recommendations are given, how to determine it, specifically in the case of LC–MS methods.     

A new effective on chip electromembrane extraction coupled with high performance liquid chromatography for enhancement of extraction efficiency

In the present research, an effective on chip electromembrane extraction (CEME) coupled with high performance liquid chromatography was presented for analysis of nortriptyline (NOR) and amitriptyline (AMI) as basic model analytes from urine samples. The chip consists of two polymethyl methacrylate (PMMA) parts with two craved microfluidic channels in each part. These channels were used as flow path for the sample solution and a thin compartment for the acceptor phase. A porous polypropylene sheet membrane impregnated with an organic solvent was placed between two parts of chip device to separate the channels. Two platinum electrodes were mounted at the bottom of these channels that were connected to a power supply providing the electrical driving force for migration of ionized analytes from sample solution through the porous sheet membrane into the acceptor phase. This new setup provides effective and reproducible extractions with low volume of sample solution. Efficient parameters on CEME of the model analytes were optimized using one variable at a time method. Under the optimized conditions, the calibration curve was linear in the range of 10.0–500 μg L⁻¹ with coefficient of determination (r²) more than 0.9902. The relative standard deviations (RSDs %) for extraction and determination of the analytes were less than 6.8% based on six replicate measurements. LODs less than 4.0 μg L⁻¹ were obtained for both of the model analytes. The preconcentration factors higher than 17.0-fold were obtained. The results demonstrated that CEME would be used efficiently for extraction and determination of AMI and NOR from urine samples.     

Advanced analytical methods for the structure elucidation of polystyrene-b-poly(n-butyl acrylate) block copolymers prepared by reverse iodine transfer polymerisation

Reverse iodine transfer polymerisation (RITP) is a living radical polymerisation technique that has shown to be feasible in synthesising segmented styrene-acrylate copolymers. Polymers synthesised via RITP are typically only described regarding their bulk properties using nuclear magnetic resonance spectroscopy and size exclusion chromatography. To fully understand the complex composition of the polymerisation products and the RITP reaction mechanism, however, it is necessary to use a combination of advanced analytical methods. In the present RITP procedure, polystyrene was synthesised first and then used as a macroinitiator to synthesise polystyrene-block-poly(n-butyl acrylate) (PS-b-PBA) block copolymers. For the first time, these PS-b-PBA block copolymers were analysed by a combination of SEC, in situ¹H NMR and HPLC. ¹H NMR was used to determine the copolymer composition and the end group functionality of the samples, while SEC and HPLC were used to confirm the formation of block copolymers. Detailed information on the living character of the RITP process was obtained.     

Novel application of liquid chromatography/mass spectrometry for the characterization of drying oils in art: Elucidation on the composition of original paint materials used by Edvard Munch (1863–1944)

Modern oil paints, introduced at the beginning of the 20th century, differ from those classically used in antiquity in their chemical and compositional features. The main ingredients were still traditional drying oils, often used in mixtures with less expensive oils and added with several classes of additives. Consequently, detailed lipid profiling, together with the study of lipid degradation processes, is essential for the knowledge and the conservation of paint materials used in modern and contemporary art.     

The tribological performance of fullerene‐like hydrogenated carbon films under ionic liquid lubrication

Fullerene‐like hydrogenated carbon films were deposited on Si substrate by plasma‐enhanced chemical vapor deposition. The microstructures of films were characterized by high‐resolution transmission electron microscopy and Raman spectrum. The tribological performance of films was tested by reciprocating ball‐on‐disc tester under 1‐ethyl‐3‐methylimidazolium tetrafluoroborate ionic liquid. The surface morphology and chemical composition of wear tracks and wear rates were investigated by optical microscope, X‐ray photoelectron spectroscopy, and 3D surface profiler. The results indicated that the film with a typical fullerene‐like structure embedded into the amorphous sp² and sp³ carbon networks could be prepared successfully, and the film shows a higher hardness (26.7 GPa) and elastic recovery (89.9%) compared with the amorphous carbon film. Furthermore, the film shows a lower friction coefficient at low contact load and friction frequency, and excellent wear‐resistance performance at high load and frequency under ionic liquid lubrication. Meanwhile, the wear life of fullerene‐like hydrogenated carbon films could be improved significantly using ionic liquid as a lubrication material. Copyright © 2015 John Wiley & Sons, Ltd.     

Effects of anodic oxidation on corrosion properties of Al coating by arc spraying in seawater

A layer of Al coatings was prepared on the S355 steel by arc spraying, which was conducted by anodic oxidation treatment; the morphologies, chemical element compositions and phases of Al coating, and anodic oxide layer were analyzed with field emission scanning electron microscope (FESEM), energy dispersive spectrometer (EDS) and X‐ray diffraction (XRD), respectively. The corrosion protections of Al coating before and after anodic oxidation were discussed with a seawater immersion test; the corrosion resistance mechanisms of Al coating and anodic oxide layer in the seawater were also investigated. The results show that the thickness of Al coating is about 300 µm by arc spraying, the sample surfaces become loose after seawater immersion corrosion and Cl^? and O^2? penetrate into the substrate from the cracks, destroying the binding properties of coating–substrate, and the coating fails. After anodic oxidation, the oxide layer is formed in the surface of Al coating with the thickness of about 30 µm; the corrosion products are mainly composed of Al(OH)₃, which barraged the holes caused by seawater corrosion. The corrosion cracks are formed during the corrosion, while the number and depth of cracks decrease obviously after anodic oxidation treatment. The corrosion of Al coating becomes the local corrosion after anodic oxidation treatment, and the grains are smaller, which are easily nucleated to form a new corrosion resistance layer. Copyright © 2015 John Wiley & Sons, Ltd.